Shower installation in Newburn

Postcode districts: NE5, NE15
Nearby: Blaydon-on-Tyne, Whickham and Gosforth
Guide price: £400–£3,200
Typical time on site: half a day to 3 days
Water: Soft across most of Tyne and Wear
Survey: Free, at your home

What does a new shower cost in Newburn?

In Newburn, a new shower typically costs £400–£3,200 including VAT, based on North East England prices. Prices in North East England run at about 10% below the national guide, mainly because of labour rates. The figure depends on the size of the room, whether anything moves, and the products you pick.

Shower swap

£400–£900

Like-for-like mixer or electric shower

Typical

New shower over bath

£700–£1,600

Bath screen

New shower with enclosure

£1,350–£3,200

Tiling to the enclosure

Guide prices for Newburn including VAT. Your itemised written quote after the free survey is the price that counts.

Working in Newburn

We work right across Newburn — NE5 and NE15 — and in neighbouring Blaydon-on-Tyne and Whickham.

In Newburn, as anywhere, the age of the house decides a lot: pipe sizes, floor construction and where the soil stack runs. For Newburn homes with a cold tank in the loft, we check the system before fitting anything, because a pump is only allowed on a gravity supply. We test pressure and flow at Newburn surveys before recommending a shower, so you know how it will perform before you buy.

Supplies across most of Tyne and Wear are soft. If that holds for your street in Newburn, limescale on shower glass and heads builds up slowly and a squeegee after use is usually enough. Hardness varies street by street, so check the figure for your postcode with your water supplier.

What the job includes

A bath screen, tray or enclosure where the shower is new
Tiling or re-tiling around the shower, with tanking behind new tiles in the wet area
Removal of the old shower, a full-flow test and a handover on isolating and descaling it
New pipework and isolation valves, plus a pump only where the system is gravity-fed from a cold tank

Decisions to make first

Thermostatic mixer

Blends hot and cold from your system and holds the temperature steady when someone runs a tap. The usual choice with a combi or an unvented cylinder.

Electric shower

Heats cold mains water as it flows, so it works without stored hot water. Higher kW units give more flow; 8.5 to 10.5 kW models need a dedicated circuit, often 40 to 45 amps.

Rules that apply in England

In England, an electric shower usually needs its own dedicated circuit, often 40 to 45 amps for an 8.5 to 10.5 kW unit, and a new circuit is notifiable under Part P. The Part G limit of 48 °C applies to a new bath in a new dwelling or one created by change of use, not to a shower, but a thermostatic valve gives similar protection. An unvented cylinder fitted to improve the shower must be installed by a G3-qualified installer.

More about shower installation

Shower installation in Newburn: questions

How much should I budget for a new shower in Newburn?

A new shower in Newburn usually costs £400–£3,200 including VAT. The final figure comes down to what you choose and what we find at the survey; your written quote lists every item so you can see where the money goes.

Is the water hard in Newburn?

Who handles building control for a new shower in Newburn?

Building control for Newburn is handled by the local council or an approved inspector. If your job needs sign-off — for example a new circuit, new drainage or a new extractor where there was none — we tell you at the survey and handle the notification as part of the work.

How long does a new shower take?

Allow half a day to 3 days on site for most jobs, plus the lead time for products after you approve the quote. We give you a day-by-day plan before work starts in Newburn.

Does an electric shower need its own circuit?

Almost always. An electric shower draws a large current, so it needs a dedicated circuit from the consumer unit, often 40 to 45 amps for an 8.5 to 10.5 kW unit, with RCD protection. In England and Wales a new circuit is notifiable work. Swapping like for like onto an adequate existing circuit is simpler.