Shower installation in Urmston

Postcode districts: M17, M32, M41
Nearby: Stretford, Sale and Eccles
Guide price: £400–£3,300
Typical time on site: half a day to 3 days
Water: Soft across most of Greater Manchester
Survey: Free, at your home

What does a new shower cost in Urmston?

As a guide, budget £400 to £3,300 including VAT for a new shower in Urmston; your written quote will pin it down. We adjust the national guide for North West England, where prices are typically about 6% below the UK average. The figure depends on the size of the room, whether anything moves, and the products you pick.

Shower swap

£400–£950

Test and handover

Typical

New shower over bath

£750–£1,700

Thermostatic bar shower and riser

New shower with enclosure

£1,400–£3,300

Pipework and waste

Guide prices for Urmston including VAT. Your itemised written quote after the free survey is the price that counts.

Working in Urmston

We work right across Urmston — M17, M32 and M41 — and in neighbouring Stretford and Sale.

Homes in and around Urmston vary, so we look at the floor, the walls and the water system before we price anything. If the shower in your Urmston home swings between hot and cold, a thermostatic valve is usually the fix. If you want a shower in your Urmston home that works when the boiler is off, an electric shower is worth considering, as long as the consumer unit can take the circuit.

Supplies across most of Greater Manchester are soft. If that holds for your street in Urmston, limescale on shower glass and heads builds up slowly and a squeegee after use is usually enough. Hardness varies street by street, so check the figure for your postcode with your water supplier.

What the job includes

Electrical connection by a qualified electrician, tested and certified
A bath screen, tray or enclosure where the shower is new
A check of your hot-water system, water pressure and flow rate
Removal of the old shower, a full-flow test and a handover on isolating and descaling it

Decisions to make first

Electric shower

Heats cold mains water as it flows, so it works without stored hot water. Higher kW units give more flow; 8.5 to 10.5 kW models need a dedicated circuit, often 40 to 45 amps.

Digital shower

A wall panel sets the exact temperature and flow, while the mixing valve sits out of sight. It needs a power supply and suits a clean, concealed look.

Rules that apply in England

In England, an electric shower usually needs its own dedicated circuit, often 40 to 45 amps for an 8.5 to 10.5 kW unit, and a new circuit is notifiable under Part P. The Part G limit of 48 °C applies to a new bath in a new dwelling or one created by change of use, not to a shower, but a thermostatic valve gives similar protection. An unvented cylinder fitted to improve the shower must be installed by a G3-qualified installer.

More about shower installation

Shower installation in Urmston: questions

How much does a new shower cost in Urmston?

A new shower in Urmston usually costs £400–£3,300 including VAT. Where you land in that range depends on the size of the room, whether the layout changes and the products you choose. After the free survey you get an itemised written quote, and the price is fixed in writing once the layout and products are agreed.

Who handles building control for a new shower in Urmston?

Building control for Urmston is handled by the local council or an approved inspector. If your job needs sign-off — for example a new circuit, new drainage or a new extractor where there was none — we tell you at the survey and handle the notification as part of the work.

How long does a new shower take?

Allow half a day to 3 days on site for most jobs, plus the lead time for products after you approve the quote. We give you a day-by-day plan before work starts in Urmston.

Is the home survey in Urmston really free?

Yes. We visit, measure the room, check the pipework, drainage and electrics, and talk through what you want. You then get a written, itemised quote with no obligation to go ahead.

Can I fit a shower pump with a combi boiler?

No. A combi boiler takes its water from the mains, and connecting a pump directly to the mains supply is not allowed under the water fittings regulations. Shower pumps are only for gravity systems with a cold tank. If a combi shower is weak, the cause is usually the incoming flow, the boiler output or the head, not something a pump can fix.