Shower installation in Canterbury

Postcode districts: CT1, CT2, CT5, CT6
Nearby: Whitstable, Herne Bay and Faversham
Guide price: £500–£3,900
Typical time on site: half a day to 3 days
Water: Very hard across most of Kent
Survey: Free, at your home

What does a new shower cost in Canterbury?

As a guide, budget £500 to £3,900 including VAT for a new shower in Canterbury; your written quote will pin it down. Prices in South East England run at about 12% above the national guide, mainly because of labour rates. The figure depends on the size of the room, whether anything moves, and the products you pick.

Shower swap

£500–£1,100

Test and handover

Typical

New shower over bath

£900–£2,000

Thermostatic bar shower and riser

New shower with enclosure

£1,700–£3,900

Pipework and waste

Guide prices for Canterbury including VAT. Your itemised written quote after the free survey is the price that counts.

Working in Canterbury

We work right across Canterbury — CT1, CT2, CT5 and 1 more postcode districts — and in neighbouring Whitstable and Herne Bay.

Canterbury is a big place with every kind of home, from terraces to flats to new builds, so we never price from a photo alone. If you are replacing a failed electric shower in Canterbury, we check whether the existing cable and circuit suit the new unit. We test pressure and flow at Canterbury surveys before recommending a shower, so you know how it will perform before you buy.

Supplies across most of Kent are very hard. If your supply in Canterbury is the same, limescale on shower glass and heads is a real issue: easy-clean glass, rub-clean nozzles and a squeegee make a big difference. Hardness varies street by street, so check the figure for your postcode with your water supplier.

What the job includes

For an electric shower, a check of the consumer unit and whether a new dedicated circuit is needed
New pipework and isolation valves, plus a pump only where the system is gravity-fed from a cold tank
Supply and fitting of the shower valve or unit, riser rail, handset or fixed head
Electrical connection by a qualified electrician, tested and certified

Decisions to make first

Digital shower

A wall panel sets the exact temperature and flow, while the mixing valve sits out of sight. It needs a power supply and suits a clean, concealed look.

Thermostatic mixer

Blends hot and cold from your system and holds the temperature steady when someone runs a tap. The usual choice with a combi or an unvented cylinder.

Rules that apply in England

In England, an electric shower usually needs its own dedicated circuit, often 40 to 45 amps for an 8.5 to 10.5 kW unit, and a new circuit is notifiable under Part P. The Part G limit of 48 °C applies to a new bath in a new dwelling or one created by change of use, not to a shower, but a thermostatic valve gives similar protection. An unvented cylinder fitted to improve the shower must be installed by a G3-qualified installer.

More about shower installation

Shower installation in Canterbury: questions

How much should I budget for a new shower in Canterbury?

A new shower in Canterbury usually costs £500–£3,900 including VAT. Where you land in that range depends on the size of the room, whether the layout changes and the products you choose. After the free survey you get an itemised written quote, and the price is fixed in writing once the layout and products are agreed.

Is the water hard in Canterbury?

Who handles building control for a new shower in Canterbury?

Building control for Canterbury is handled by the local council or an approved inspector. If your job needs sign-off — for example a new circuit, new drainage or a new extractor where there was none — we tell you at the survey and handle the notification as part of the work.

How long does a new shower take?

Allow half a day to 3 days on site for most jobs, plus the lead time for products after you approve the quote. We give you a day-by-day plan before work starts in Canterbury.

Does an electric shower need its own circuit?

Almost always. An electric shower draws a large current, so it needs a dedicated circuit from the consumer unit, often 40 to 45 amps for an 8.5 to 10.5 kW unit, with RCD protection. In England and Wales a new circuit is notifiable work. Swapping like for like onto an adequate existing circuit is simpler.